behars Loading... Please wait...

Window Defroster and Grid Line Repair Kit

$17.99
Shipping:
Calculated at checkout
Quantity:

Product Description

How To Repair Your Window Defroster Grid

With Epoxy International's Defogger Repair Kit


Atom Adhesives Window Defroster Repair KitBroken Window Defroster Grid

Window Defroster Grid Repair Kit:

The Window Defroster Grid Repair kit is an epoxy adhesive and coating formulation based on pure silver. This versatile silver formulation offers the maximum continuity of conductivity with an electrical resistivity value of less than 1x10-4 ohm.cm.

Our Defroster/Window Grid Repair kit is also characterized by a wide operating temperature range from –50 to +170°C.

This Defroster/Window Grid Repair kit is recommended for grid repair, electronic bonding, or sealing applications that require both fine electrical and mechanical properties. It can Substrates also aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.

How To Find The Damaged Grid Lines:

You can follow this video:


How To Repair Window Defogger Strip:

Windshield defogger strip

Put the measuring lead (Red) and the reference (Black) of the Multimeter on the damaged grid line at both ends, right where the grid connects with the wide bus bars. Move one probe--it doesn't matter which--to the center of the line. If you now read 6 volts, the scratch is not in between the two probes. If you read the same system voltage, 12 volts or so, the break is in between the old probe location and the new one. Just move the probes until you find the location that has full system voltage spanning it. Now it's time to turn off the de¬froster grid and the ignition switch.

How To Repair The Defroster Tab:

 
  1. Clean the tab and the contact area with the alcohol prep. Then apply activator to both surfaces and let it dry.
  2. Apply the completely mixed adhesive kit to the prepared surfaces, and gently press these surfaces together. Contact pressure is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured.
  3. Press the tab onto the contact area. Use masking tape to keep all parts held in place as it takes 24 hours at 50F or higher to dry.  If the temperature is lower than 50F, then wait 48 hours.  Please wait 24 to 48 hours before using the defogger.

Defroster TABS:

The tabs located along the sides of the defroster connect the defroster electrically to the vehicles defrost circuit. One tab is the positive and the other ground. If a tab comes off the defroster this will mean total instantaneous failure of the defroster.

  1. Our kit is an epoxy adhesive. To use, carefully clean and dry all surfaces to be bonded from all dirt, dust, debris and handprints from the rear window.
  2. Apply the completely mixed adhesive kit to the prepared surfaces, and gently press these surfaces together. Contact pressure is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured.
  3. Some separation of components is common during shipping and storage. For this reason, it is recommended that the contents of the shipping container be thoroughly mixed prior to use.
  4. Some ingredients in this formulation provided may crystallize when subjected to low temperature storage. A gentle warming cycle of 52°C for 30 minutes prior to mixing components may be necessary. Crystallized epoxy components do not react as well as liquid components and should be re-dissolved prior to use for best results.

Easy Mixing Pouch Instructions:

Easy mixing burst pouch instructions

Misc Properties:

Hardness, Shore D 83
Shrinkage linear in/in 0.003
Lap shear strength, psi 9400
Volume Resistivity ohm cm = 0.0001

Cure Schedule:

2 minutes @ 120°C
5 minutes @ 100°C
12 hours @ 25°C

General Properties:

Cure Type Heat Cure or Room Temperature
Benefits
  • High strength
  • Perfect bond
  • Cold solder replacement
Mix Ratio 100:7 Resin:Hardener

Prices & Packaging



10gm syringes for $34.99 + Shipping
(enough for approx. 10 repairs)



2.5gm pouch for $14.99 + Shipping

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

TDS | SDS

Back to Top