How do I use this pouch?

Silver-Bond 6 Low Cost, Low Volume Resistivity, Electrically Conductive Silver Epoxy Adhesive

1 product review

$7.25

Shipping:

Calculated at checkout

* Size:

1.5gm pouch(s)
2.5gm pouch(s)
5gm pouch(s)
10gm pouch(s)
50gm kit(s)
100gm kit(s)
250gm kit(s)
500gm kit(s)

Quantity:

TDS
Product Review
Find Similar Products by Category

Product Description

PRODUCT DESCRIPTION:

Silver-Bond 6 Low Cost, Low Volume Resistivity, Electrically Conductive Silver Epoxy Adhesive represents the newest technology since the introduction of electrically conductive silver compounds. This unique formulation is based on a silver coated ceramic that results in lower material costs without adversely sacrificing the properties obtained with a pure silver formulation. This concept opens the door to a wide range of applications previously prohibited by the much higher cost of conventional silver conductive.

Silver-Bond 6 Low Cost, Low Volume Resistivity, Electrically Conductive Silver Epoxy Adhesive cures at room temperature or can be accelerated with mild heat to form a tenacious bond between similar and dissimilar substrates such as aluminum, copper, magnesium, steel, bronze nickel, ceramic, glass, phenolic, and G-10 epoxy glass boards.

Silver-Bond 6 Low Cost, Low Volume Resistivity, Electrically Conductive Silver Epoxy Adhesive, because of its excellent continuity, has been used extensively in such diversified applications as, microwave EMI and RFI shielding, in the assembly or repair of printed circuit boards, wave guides, electronic modules, flat cable, high frequency shields, connections, and circuitry and as a cold solder. This unique formulation offers ease in handling due to its creamy consistency and versatile application by hand, automatic dispenser, silk-screening, transfer or stamping techniques.

PRODUCT PROPERTIES:

Appearance	Silver
Cure Type	Heat cure or Room temperature
Benefits	High strength Perfect bond EMI & RFI shielding Cold Solder
Minimum Bond Line Thickness	1mm
Glass Transition Temp, Tg	50 C
Substrates	Excellent choice aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.
Typical Applications	microwave EMI and RFI shielding, in the assembly or repair of printed circuit boards, wave guides, electronic modules, flat cable, high frequency shields, connections, and circuitry and as a cold solder.

UNCURED PROPERTIES:

Viscosity @ 25 C cps	Paste
Silver coated ceramic , %	50 to 75
Pot Life @ RT	1 Hour
Mix ratio, by weight	100:5 / Resin:Hardener
Shelf life	1 Year

CURE SCHEDULE:

15 minutes	@ 100C
30 minutes	@ 60C
24 hours	@ Room temperature

CURED PROPERTIES:

Volume Resistivity	< 0.0015
Hardness, Shore D	81
Compressive Strength, psi	13,600
Shrinkage Linear, in / in	0.004
Specific Gravity, 25C / 25C	2.60
Tensile Strength, psi	8,900
Compressive Strength, psi	13,700

THERMAL PROPERTIES:

Thermal Conductivity, btu / hr / ft2 / F / in	90
Thermal Expansion Coefficient, (cm / cm / C 10-5)	1.9
Heat Distortion, C	165
Operating Temperature Range, C	-50 to +165

GENERAL INFORMATION:

For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).

HOW TO USE:

1) Carefully clean and dry all surfaces to be bonded.

2) Apply Silver-Bond 6 Low Cost, Low Volume Resistivity, Electrically Conductive Silver Epoxy Adhesive completely mixed adhesive to the prepared surfaces, and gently press these surfaces together. Contact pressure is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured.

3) Some separation of components is common during shipping and storage. For this reason, it is recommended that the contents of the shipping container be thoroughly mixed prior to use.

4) Some ingredients in this formulation provided may crystallize when subjected to low temperature storage. A gentle warming cycle of 52C for 30 minutes prior to mixing components may be necessary. Crystallized epoxy components do not react as well as liquid components and should be re-dissolved prior to use for best results.

AVAILABILITY:

This epoxy can be supplied in various different packages.

Product Reviews

Write Review

This worked very well on my project.

Posted by Unknown on Mar 29th 2017

I needed to secure a small wire to a glass solar panel with a very thin conductive surface.
This product adhered well and restored conductivity.